Click for new scientific resources and news about Corona[COVID-19]

Paper Information

Journal:   JOURNAL OF APPLIED FLUID MECHANICS (JAFM)   2016 , Volume 9 , Number 5; Page(s) 2149 To 2160.
 
Paper: 

AXIAL-FLOW COMPRESSOR PERFORMANCE PREDICTION IN DESIGN AND OFF-DESIGN CONDITIONS THROUGH 1-D AND 3-D MODELING AND EXPERIMENTAL STUDY

 
 
Author(s):  PEYVAN A., BENISI A.H.*
 
* SCHOOL OF MECHANICAL ENGINEERING, SHARIF UNIVERSITY OF TECHNOLOGY, TEHRAN, IRAN
 
Abstract: 

In this study, the main objective is to develop a one dimensional model to predict design and off design performance of an operational axial flow compressor by considering the whole gas turbine assembly. The design and off-design performance of a single stage axial compressor are predicted through 1D and 3D modeling. In one dimensional model the mass, momentum and energy conservation equations and ideal gas equation of state are solved in mean line at three axial stations including rotor inlet, rotor outlet and stator outlet. The total to total efficiency and pressure ratio are forecasted using the compressor geometry, inlet stagnation temperature and stagnation pressure, the mass flow rate and the rotational speed of the rotor, and the available empirical correlation predicting the losses. By changing the mass flow rate while the rotational speed is fixed, characteristic curves of the compressor are obtained. The 3D modeling is accomplished with CFD method to verify one dimensional code at non-running line conditions. By defining the three dimensional geometry of the compressor and the boundary conditions coinciding with one dimensional model for the numerical solver, axial compressor behavior is predicted for various mass flow rates in different rotational speeds. Experimental data are obtained from tests of the axial compressor of a gas turbine engine in Sharif University gas turbine laboratory and consequently the running line is attained. As a result, the two important extremities of compressor performance including surge and choking conditions are obtained through 1D and 3D modeling. Moreover, by comparing the results of one-dimensional and three-dimensional models with experimental results, good agreement is observed. The maximum differences of pressure ratio and isentropic efficiency of one dimensional modeling with experimental results are 2.1 and 3.4 percent, respectively.

 
Keyword(s): AXIAL COMPRESSOR, ONE DIMENSIONAL MODELING, THREE DIMENSIONAL MODELING, CHARACTERISTIC CURVE
 
 
References: 
  • Not Registered.
  •  
  •  
 
Citations: 
  • Not Registered.
 
+ Click to Cite.
APA: Copy

PEYVAN, A., & BENISI, A. (2016). AXIAL-FLOW COMPRESSOR PERFORMANCE PREDICTION IN DESIGN AND OFF-DESIGN CONDITIONS THROUGH 1-D AND 3-D MODELING AND EXPERIMENTAL STUDY. JOURNAL OF APPLIED FLUID MECHANICS (JAFM), 9(5), 2149-2160. https://www.sid.ir/en/journal/ViewPaper.aspx?id=571707



Vancouver: Copy

PEYVAN A., BENISI A.H.. AXIAL-FLOW COMPRESSOR PERFORMANCE PREDICTION IN DESIGN AND OFF-DESIGN CONDITIONS THROUGH 1-D AND 3-D MODELING AND EXPERIMENTAL STUDY. JOURNAL OF APPLIED FLUID MECHANICS (JAFM). 2016 [cited 2021August04];9(5):2149-2160. Available from: https://www.sid.ir/en/journal/ViewPaper.aspx?id=571707



IEEE: Copy

PEYVAN, A., BENISI, A., 2016. AXIAL-FLOW COMPRESSOR PERFORMANCE PREDICTION IN DESIGN AND OFF-DESIGN CONDITIONS THROUGH 1-D AND 3-D MODELING AND EXPERIMENTAL STUDY. JOURNAL OF APPLIED FLUID MECHANICS (JAFM), [online] 9(5), pp.2149-2160. Available: https://www.sid.ir/en/journal/ViewPaper.aspx?id=571707.



 
  pdf-File
Yearly Visit 77
 
 
Latest on Blog
Enter SID Blog