List Of Volumes: 11 Volume(s) Year 2022 Volume 23, Number 2 Year 2021 Year 2020 Year 2019 Year 2018 Year 2017 Year 2016 Year 2015 Year 2014 Year 2011 Year 2010
List Of Journal Paper(s): SEMI-ANNUALLY JOURNAL OF AERONAUTICAL ENGINEERING (JOAE):Fall 2021-Winter 2022, Volume 23, Number 2 12 Paper(s) 1 : Optimal Control of UAV Fuel Consumption during Circular Loitering Flight Author(s): Moosavi Abolfazl,Sadati Seyed Hosein*,Karimi Jalal Page(s): From 0 To 0 Keyword(s): Optimal control,Pontryagen minimum principle,Fuel consumption,Loitering,Multiple shooting method Reference(s): (0) Citation(s): (0) 2 : Design, Analysis and Manufacturing of One-Manned Coaxial Electric Helicopter Author(s): MAHDIAN ASGHAR*,Sebghatollahy Farhad Page(s): From 0 To 0 Keyword(s): Electric helicopter,One-maned helicopter,Coaxial blades Reference(s): (0) Citation(s): (0) 3 : Experimental Investigation of Suddenly Stop of Supercritical Airfoil SC-0410 between Pitching Motion Author(s): Eslami Haghighat Zahra* Page(s): From 0 To 0 Keyword(s): Reduced frequency,Hysteresis loop,Lift coefficient,Supercritical airfoil Reference(s): (0) Citation(s): (0) 4 : Analysis of Liquid Fuel Spray in an Evaporating Chamber Author(s): ABEDINEJAD MOHAMMAD SADEGH* Page(s): From 0 To 0 Keyword(s): Two-phase flow,Eulerian-Lagrangian spray,Secondary break-up,Gravity,Radiation heat transfer,Evaporation of droplets Reference(s): (0) Citation(s): (0) 5 : Effect of Optimized Roughness Distribution Elements on the Behavior of Phase Portrait Circuits in Critical Reynolds Author(s): JABBARI HOSSEIN,ESMAEILI ALI,Djavareshkian Mohammad Hasan* Page(s): From 0 To 0 Keyword(s): Micro Aerial Vehicle (MAV),Laminar Separation Bubble (LSB),Roughness element,Critical Reynolds,Passive flow control,Frequencies analysis,Phase portrait Reference(s): (0) Citation(s): (0) 6 : Synthesis of epoxy substrate graphene oxide nanoparticles with the approach of reducing RCS and increasing the thermal resistance of UAVs Author(s): Aslinezhad Mehdi*,Malekijavan Alireza,Hoseinzadeh Masoud Page(s): From 0 To 0 Keyword(s): Reduce radar cross section,Graphene oxide,Electromagnetic waves,Epoxy resin Reference(s): (0) Citation(s): (0) 7 : Satellite Attitude Control Using Modified PID Controller in the Presence of Uncertainty Author(s): BOHLOURI VAHID* Page(s): From 0 To 0 Keyword(s): Satellite attitude control,Modified PID control,Uncertainty,Reaction wheel,Optimization Reference(s): (0) Citation(s): (0) 8 : Requirements for Equipping Tau Anti-Tank Short-Range Missile with Inertial Guidance and Navigation System Author(s): KARIMI JAVAD*,Hosseni Saeed Mohamad Page(s): From 0 To 0 Keyword(s): Short-range projectiles,Accelerometer sensor error,Inertia guidance and navigation Reference(s): (0) Citation(s): (0) 9 : Optimization and Design of General Aviation Aircrafts Wing Using Non-Dominated Sorting Genetic Algorithms II Author(s): PAZOOKI FARSHAD,Zibafar Amirreza*,Rahmati Mostafa Page(s): From 0 To 0 Keyword(s): Optimization,General Aviation,Wing Design,Genetic Algorithm Reference(s): (0) Citation(s): (0) 10 : Semi-empirical Electromechanical Model for Pulsed Plasma Thrusters Using Two Different Approaches and Comparison with Experimental Results Author(s): Oloumi Mohsen,Movahedi Nejad Hadi,Rostamifard Dariush*,Hosseinkhani Hassan,KIANI AMIR Page(s): From 0 To 0 Keyword(s): Pulsed plasma thrusters,Electromechanical model,Semi-empirical model,Slug model,Snowplow model Reference(s): (0) Citation(s): (0) 11 : Experimental Study of Two-Dimensional and Axisymmetric Pneumatic Contact Grippers for Limp and Porous Materials Author(s): HOJAJI MOHAMMAD*,Salarpour Setayesh,Hakimi Meysam,Babaie Pouladi Laya Page(s): From 0 To 0 Keyword(s): Gripper,Contact gripper,Dual-throat ejector,Limp and porous materials Reference(s): (0) Citation(s): (0) 12 : Numerical study of the effect of rectangular finlets on the turbulent boundary layer trailing edge noise of a flat edge Author(s): farmani Mohammad*,DEHGHAN ALI AKBAR,Zabihinejad Milad Page(s): From 0 To 0 Keyword(s): Simulation,Finlet,Trailing edge noise,Turbulent boundary layer,Flat plate Reference(s): (0) Citation(s): (0)